Categories
Mechanical Engineering

Write a short report (not exceeding 2 page excluding the reference list, based o

Write a short report (not exceeding 2 page excluding the reference list based on APA Style (Double spacing)) Explaining Why calibrate? What does calibrated mean? In your own words. Make sure you include the reference list also (Minimum 3 references). 2 pages report include introduction main body and conclusion.

Categories
Mechanical Engineering

Draw three independent connectors that will fail in shear, normal, and bearing s

Draw three independent connectors that will fail in shear, normal, and bearing stress between5 kN and 7 kN. opted to define failure as plastic deformation or stress beyond the yield point.could you assist me in calculating and developing a bearing-stress-resistant connector? (Compressive stress)
Requirements: Explanation   |   .doc file

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering question and need an expl

Learning Goal: I’m working on a mechanical engineering question and need an explanation to help me learn.I have fatigue problem about stress and deflection. I need help with finding all the equations require to solve this problem and what are the steps to solve the problem.
Requirements: Clear explanation   |   .doc file

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering discussion question and n

Learning Goal: I’m working on a mechanical engineering discussion question and need support to help me learn.the question are uploadedhere is some links to help you with solidworks you need to be good at dynamics of mechanics and solidworks
Requirements: as needed

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering question and need support

Learning Goal: I’m working on a mechanical engineering question and need support to help me learn.the question are uploadedhere is some links to help you with solidworks you need to be good at dynamics of mechanics and solidworks
Requirements: as needed   |   .doc file

Categories
Mechanical Engineering

protection phone case from heating and cooling. proposal the Executive Summary f

protection phone case from heating and cooling. proposal the Executive Summary fulfills three purposes: It gives some clue as to how the report is organized, including a list of the subsystems.
It summarizes the content of the proposal, including the problem statement and proposed solution.
3- It gives the time during which the work will be done and cost. In this case, the total real dollars you expect to spend300-500 words
Requirements: 1 page

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering exercise and need an expl

Learning Goal: I’m working on a mechanical engineering exercise and need an explanation to help me learn.I have a 3 problems about torsion load and combined load that I need help to understand how to solve them.
Requirements: enough information to understand the subject

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering discussion question and n

Learning Goal: I’m working on a mechanical engineering discussion question and need guidance to help me learn. please help me do Plate 2-331 and Plate 2-38_Slider Block (be aware that you will need SOLIDWORKS software in order to do this question) Open attached file and design plates: 3-50, 2-343, 2-38_Slider Block, 5-352, 2-331, 2-332. Thickness for 3-50 plate is 0.25″.Plate 2-331: fully defined sketch, extrusion to thickness 0.25″Plate 2-38_Slider Block: fully defined sketch, extrusion to thickness 0.25″
Requirements: normal

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering question and need guidanc

Learning Goal: I’m working on a mechanical engineering question and need guidance to help me learn. please help me do Plate 2-331 and Plate 2-38_Slider Block (be aware that you will need SOLIDWORKS software in order to do this question) Open attached file and design plates: 3-50, 2-343, 2-38_Slider Block, 5-352, 2-331, 2-332. Thickness for 3-50 plate is 0.25″.Plate 2-331: fully defined sketch, extrusion to thickness 0.25″Plate 2-38_Slider Block: fully defined sketch, extrusion to thickness 0.25″
Requirements: normal

Categories
Mechanical Engineering

Learning Goal: I’m working on a mechanical engineering question and need support

Learning Goal: I’m working on a mechanical engineering question and need support to help me learn.please help me do Plate 2-331 and Plate 2-38_Slider BlockOpen attached file and design plates: 3-50, 2-343, 2-38_Slider Block, 5-352, 2-331, 2-332. Thickness for 3-50 plate is 0.25″.Plate 2-331: fully defined sketch, extrusion to thickness 0.25″Plate 2-38_Slider Block: fully defined sketch, extrusion to thickness 0.25″
Requirements: normal